Tesla certified
Tesla Wall Connector Installation in Sunnyvale
Certified Wall Connector installs across Sunnyvale and along the Lawrence Expressway corridor, commissioned and tested before we leave.
Manufacturer certified
Wall Connector Installs Done to Tesla's Spec in Sunnyvale
The Wall Connector is the fastest home charging option for a Tesla, and it is also the one people most often get wired at the wrong amperage. Tesla Wall Connector installation in Sunnyvale starts with the same question as every other job here: what can your service actually carry on a continuous load. Sunnyvale EV Charger Installation is Tesla-certified, which means we install to the manufacturer specification and commission the unit properly instead of just energizing it. Most calls come from drivers who have just taken delivery or who are replacing a mobile connector that is no longer keeping up. The install is typically one visit, and the difference between a good one and a bad one shows up months later in whether the unit ever throttles or faults.
Tesla-certified installation, Gen 3 units included
Amperage configured to what your service can hold
Wi-Fi commissioning and firmware confirmed on site
Power sharing set up for two-Tesla driveways
What a Wall Connector Installation Includes
Everything that goes into a Wall Connector install, including the parts people do not think about.
Load calculation and amperage decisionThe Wall Connector is configurable from 15 to 48 amps, and we set it to what your panel supports rather than the maximum on the box.
Correct breaker and conductor sizingA 48-amp configuration requires a 60-amp breaker and conductors rated accordingly, and getting that wrong is the most common defect we find on other people's work.
Hardwired connection to the panelThe Wall Connector is a hardwired unit, so there is no plug in the path and no receptacle to overheat, which is part of why it runs higher amperage safely.
Mounting on structure, indoors or outThe unit is rated for outdoor mounting, and we place it so the 24-foot cable reaches the port without tension and without lying across a driveway.
Wi-Fi commissioning and firmwareWe connect the unit to your network and confirm it pulls firmware, which is what enables usage reporting, remote diagnostics and future feature updates.
Power sharing configuration for multiple unitsIf there are two Teslas in the driveway, we can commission up to several units to share one circuit so they negotiate available current instead of tripping the breaker.
Charge rate verification with the vehicleBefore we leave, your car is plugged in and we confirm it is drawing the configured current rather than assuming it will.
Access control setup where wantedThe unit can be restricted to specific vehicles, which matters on shared driveways and small multi-unit properties.
City of Sunnyvale permit and inspectionFiled, scheduled and attended by us, with the signed card handed to you at the end.
Warranty registrationWe register the unit at commissioning so the manufacturer coverage starts on the correct date, and our workmanship warranty is issued in writing alongside it.
How it works
Panel Review, Written Price, Commissioned Unit
Step one
Panel review and amperage plan
We look at your service, run the load calculation, and tell you which Wall Connector configuration is realistic. If a panel upgrade is required to hit 48 amps, you hear that before you commit, not after.
Step two
Written price and scheduling
You get the itemized figure including the permit fee and the conduit run, and we book the date. Most Wall Connector installs in Sunnyvale happen within the same week as approval.
Step three
Install, commission, inspect
The circuit goes in, the unit is mounted and hardwired, then commissioned on Wi-Fi and tested against your car. The city inspection follows and we attend it.
Why Choose Us for Tesla Wall Connector Installation
Tesla-certified installation, not a generic hookup
Certification means we install and commission to Tesla's published requirements, including the firmware and network steps a lot of electricians skip. A unit that never reaches the network is a unit that cannot be diagnosed remotely or updated later.
We configure amperage honestly
Setting a Wall Connector to 48 amps on a service that cannot support it produces nuisance tripping and heat, not fast charging. We set it where it will run reliably every night, and we explain the tradeoff in plain numbers.
Multi-unit power sharing done properly
Two-Tesla households are common around Sunnyvale and Cupertino, and power sharing is the correct answer rather than two separate maxed circuits. We commission the group so the units coordinate automatically.
Book Your Sunnyvale Wall Connector Install
Get the amperage answer first and the install date second. We will tell you exactly what your service supports and what the job costs, in writing, before anything is ordered or opened.
(408) 317-9189